View and Download Scytek Electronic GALAXY G40RS product manual online. GALAXY G40RS Remote Starter pdf manual. The manufacturer will repair.

• GALAXY G40RS AUTOMATIC TRANSMISSION ONLY WITH SEPERATE LOCK/UNLOCK BUTTONS REMOTE START SYSTEM PRODUCT MANUAL. • Limited Lifetime Warranty This vehicle remote start system is warranted to the original purchaser, to be free from defects in material and workmanship. Ole Borud Shakin The Ground Raritan. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.

• Remote Transmitters Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 is a state-of-the-art remote starting system is supplied with two 4-button Remote G40RS Transmitters used to control system operations. The built-in remote start feature is designed to offer maximum convenience by remote starting your vehicle’s engine, turning on the heater/air conditioner, and then running for a pre-determined time to provide a comfortable environment once you enter your vehicle. • Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below.

Note: Up to four transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure to program all 4 transmitter memory locations. • Remote Locking To Lock the doors: 1. Turn off the ignition. Press Button 1. The doors will lock.

The parking lights will flash once. The LED will turn on, to indicate the doors are locked. 10 seconds after Locking:.

• Valet Mode The Valet Mode temporarily disables the remote start system so the vehicle may be serviced by a mechanic. The remote transmitters will continue to lock/unlock the doors. To activate or deactivate the Valet Mode: 1. Turn on the ignition. • Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. Ignition Door Unlocking For added convenience, this feature automatically unlocks the doors after the ignition key is turned off.

Driver For Flash Drive Staples 256mb Is How Many Gb. The Ignition Door Unlocking feature may also be completely disabled if desired. • Branch Feature 1. Ignition Door Locking 2. Ignition Door Unlocking 3. Door Unlock Pulse 4. Door Lock Pulse Length 5. Lock after Start 6.

Lock after Shutdown 7. Engine Run Time 8. Automatic Start Mode 9. Tachless Sense Crank Time 10. • 8-Pin Main Harness Pin 1 RED WIRE: Module Power Input (+). Connect to a constant source of +12V Pin 2 GREEN/WHITE WIRE: Brake Input (+).

Connect to the wire that shows +12V when pressing the brake. The Green/white wire is a safety shutdown wire that must be connected. Pin 3 BROWN/WHITE: Horn Output (-) 500 mA. • 2-Pin Blue Connector: Valet switch port.

Mount switch where it is accessible from the driver’s position. 30 Planos De Casa Prototipo Pdf Converter here. 2-Pin Red Connector: LED port. Mount LED where it may be easily seen from either side of the vehicle. 3-Pin White Door Lock Connector: Door lock port.. • Door Lock Diagrams Adding Actuators Negative Trigger Reverse Polarity Positive Trigger blue green Positive Horn Honk Page 10 - G 40RS.

• Control Unit G-40RS For Factory Disarm pulse use the unlock wire Enable unlock Before Start location # 12 System Programming: Added 15. Trunk Release/ Horn Out © ScyTek Electronics 2009 Wiring Diagram Green/White Brown/White Horn Output (-)500mA White White/Black Blue/Orange Remote Start output (-) When running Black Black/Gray Green Lock output.

• Galaxy 3-48C, 3-144, 3-144C, 3-520, 3-520C Installation Manual Honeywell Security. • Galaxy 3 Series Installation Manual Table of Contents Contents Introduction... 1-1 Variants...

1-1 Section 1: Quick Setup..1-3 Section 2: System Architecture..2-1 PCB Layout...2-4 RS485 Expansion Module (G3-520 only)..2-5 System Installation and Wiring.. 2-6 Connecting the Galaxy 3 Series to the PSTN. • Galaxy 3 Series Installation Manual Table of Contents Entry/Exit RIO...3-3 Entry/Exit RIO Zone Programming...3-4 Entry/Exit RIO Zone Operation... 3-4 Slave RIO....3-4 RF RIO – C076...

3-5 Connecting the RF RIO... 3-5 Addressing the RF RIO... • Galaxy 3 Series Installation Manual Table of Contents Section 4: The Galaxy Mk7 Keypad/KeyProx.4-1 General.... 4-1 Power Consumption...4-1 Wiring the Keypad/KeyProx... 4-2 Addressing...4-2 Keypad/KeyProx Installation Procedure..4-2 Volume Control...4-4 Adding a Keypad/KeyProx to the System..4-4 Removing a Keypad/KeyProx from the System.. • Galaxy 3 Series Installation Manual Table of Contents Dual Access Cards...5-7 Dual Focus (Card Held)...5-7 Timed Anti-Passback...5-7 Appendix A: Door Control - MAX (MX01).A-1 Installation Instructions...